A peer's configured role now does three more things:
- Our OPEN carries the BGP Role capability with what we are to the peer.
A peer whose own says it is something that does not pair with that, or
that sends two different roles, is refused with OPEN Message Error /
Role Mismatch. A peer that says nothing is accepted unless require_role
is set. A role on a peer in our own AS is a configuration error.
- Routes from a provider, a peer or a route server are marked Only to
Customer on the way in if they are not already, and our routes are
marked on the way out to a customer, a peer or a route server client.
- A marked route from a customer or route server client, or from a peer
with someone else's mark, is a leak and is refused. No policy setting
turns that off.
The packet crate gains the Only to Customer attribute (malformed:
treat-as-withdraw), and the Role Mismatch subcode is corrected from 8 to
11.
The status page shows whether the peer confirmed its role.
Co-Authored-By: Claude Fable 5.1 <noreply@anthropic.com>
Origin validation says who may originate a prefix and nothing about the
rest of the path: it does not catch a route leak, nor a hijack that keeps
the right origin at the end of a made-up path. ASPAs, in which a network
lists its providers, do.
bgp-rpki:
- aspa: the ASPAs and the upstream and downstream verification procedures
of draft-ietf-sidrops-aspa-verification-24, tested against the draft's
wording as written.
- rtr: protocol version 2 (draft-ietf-sidrops-8210bis-23) with the ASPA
PDU and the new error codes.
- client: asks for version 2 and falls back to whatever older version the
cache speaks; keeps ASPAs with the VRPs, applied whole or not at all;
publishes which customers' ASPAs changed; tells the cache why it is
being left (Error Report); does not ask one version's serial of another.
Server:
- A peer has a role (provider, customer, peer, route server, route server
client), which decides how its paths are verified. Without one they are
not.
- A route whose path is invalid is refused ("ASPA invalid") and held, like
one with an invalid origin; accept_aspa_invalid exempts a peer.
- When ASPAs change, routes in the table whose path has a changed customer
on it are verified again, and held routes are released when they pass
both checks.
- The revalidator finds a route's peer by index instead of searching a
list for every route.
The status page and API show each peer's role, each route's path validity,
the number of ASPAs and the RTR version in use; bgp_rpki_aspas is on
/metricz.
Co-Authored-By: Claude Fable 5.1 <noreply@anthropic.com>
A configured peer could announce any prefix with any path, in any
number, and all of it was stored and could be chosen as best. Each
peer now has an import policy, and every route goes through it before
it reaches the routing table.
Checks that hold for any peer unless turned off for it:
- no prefixes that are not routed on the Internet (private, loopback,
link-local, documentation, multicast, reserved; for IPv6, anything
outside global unicast);
- nothing longer than /24 or /48, no default route, nothing shorter
than /8 or /16;
- no reserved, private or documentation AS number in the path;
- a path that begins with the peer's own AS (turned off for a route
server), and of at most 64 AS numbers.
Always: a route with our own AS number in its path is refused. RFC 4271
requires this loop check and it was missing.
Per peer, if configured: the prefixes it may announce, each with an
optional longest more-specific, and the AS numbers its routes may
originate from. This is the list generated from the routing registries.
max_prefixes limits how many routes a peer may have. One more ends the
session with Cease / Maximum Number of Prefixes Reached, and the peer
is kept down for hold_down_seconds (ten minutes unless set): its
connections are not taken and it is not dialled. Refused routes do not
count towards the limit.
A refused route is withdrawn rather than ignored, so that it replaces
whatever the peer had announced for it before.
On a session with two-octet AS numbers the path is judged with its
AS4_PATH merged in, so that the real AS numbers are what is checked.
Peers that are not configured (accept_unconfigured_peers, for test
networks) get a policy that takes everything but loops.
Refusals are counted in bgp_routes_rejected_total by reason. The status
page and /api/peers show, for each session, how many routes the peer
has and how many were refused. The server warns at startup about peers
with no limit.
The prefix check costs about 4 ns a route with the default policy; the
end-to-end benchmark is unchanged.
Also: the benchmark's server AS is one that is in none of its generated
paths, and a table test that depended on the hasher's seed is fixed.
Co-Authored-By: Claude Fable 5.1 <noreply@anthropic.com>
